Ankündigung

Einklappen
Keine Ankündigung bisher.

T-14 mit TJ Pro???

Einklappen
X
 
  • Filter
  • Zeit
  • Anzeigen
Alles löschen
neue Beiträge

  • T-14 mit TJ Pro???

    Hi zusammen,
    habe ein Problem:
    TJ-mäßig ist alles nach Anleitung angeschlossen. Nun habe ich das Problem, dass ich ums Verrecken nicht in den Kalibrier Modus komme. Egal wie. Habe alles versucht.....Schalter/Schieber, schnell/langsam,.....
    Wie habt ihr das gelöst?

    Grüße
    Actros

  • #2
    Hi Actros,

    siehe http://www.t14-forum.net/topic.php?i...hlight=Jockey&

    RUDI
    Nicht klicken "FSK18"
    Einmal FUTABA immer FUTABA !!
    E-Mail: rudi1025[at]futaba-forum.net

    Kommentar


    • #3
      Hi Actros,

      zu beachten ist auch noch, falls du den G3 einsetzt,
      dass der TJ Sollwert Kanal nicht auf der gleichen Gruppe
      wie der Gaskanal steckt. Da nimmt der TJ nichts an und du kommst nie in den Kalibriemodus. Z. T. spinnt dann auch das Gasservo (eigene Erfahrung). Ich stecke den Sollwertkanal deshalb auf 10 und habe seither keine Probleme mehr.

      Hier noch ein Auszug aus dem T14 Zusatz zum TJ:

      Before activating the TJ, set up your heli normally with the pitch and throttle curves you would use under normal circumstances. This will ensure that should the sensor fail and the TJ reverts to transmitter throttle curves that the heli still behaves normally until a landing can be accomplished. Also ensure that this setup allows the heli to hover at your desired stick position (1/2 or ¾ as preferred) for each flight mode. The engine should be run-in and correct mixtures set.

      You must switch the governor function to any of the following channels: 4, 5, 6, 10, 11, or 12 and plug the AUX lead of the TJ into the one selected.

      You can do this under the "FUNCTION" menu.

      Also select a switch to "control" that channel. Do not select E right now. use A,B,C, or D

      Verify under "SERVO MONITOR" that the channel is going from high to low (+100 to -100) while toggling the selected switch.

      Make sure a linear curve is set for normal flight mode(0%-100%).

      Have throttle ATV's as close to 100/100 as possible.

      With the throttle stick low, turn on RX and quickly toggle selected switch from position 1 to position 3 rapidly twice: up-center-down-center-up-center-down-center-up.

      LED will flash rapidly showing calibration mode is on, move throttle stick high(yellow LED) then throttle stick low(green LED). Toggle switch once and LED will go out.

      You can now put the throttle curve points back to what they were before and select sw(E) for the GOVENOR channel under "FUNCTION" and under "control" column.

      Go to GOVERNOR screen under MODEL MENU.

      For RATE1, change ACT to ON instead of INH and change GROUP to SNGL and select sw(E) for all Flight modes.(must make these changes after selecting each flight mode with sw(E) and also the switch for Throttle hold.

      Verify that 50% on RATE(default value) will keep the green LED off for each flight mode with the throttle above 25%.

      Any value above 52% will enable the TJ.


      Grüße Andreas

      Kommentar

      Lädt...
      X